-- *****************************************************************
-- CISCO-CAS-IF-MIB.my: Channel Associated Signal Interface MIB file
--
-- July 1997 Hongchi Shih
-- Jan. 1999 Rick Chen
--
-- Copyright (c) 1997-1999, 2000, 2003 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-CAS-IF-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32FROM SNMPv2-SMI
RowStatus,TruthValue,DisplayStringFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
InterfaceIndex,ifIndex
FROM IF-MIB
CountryCode
FROM CISCO-TC
ciscoMgmt
FROM CISCO-SMI;ciscoCasIfMIB MODULE-IDENTITYLAST-UPDATED"200304180000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-voice@cisco.com"DESCRIPTION"Channel Associated Signal Interface MIB module.
This MIB manages the generic CAS (Channel Associated
Signal)or DS0 clear channel Interfaces in the router.
"REVISION"200304180000Z"DESCRIPTION"Extend ccasGrpCfgServiceType to include
h248 (9) and ds0xconn (10)"REVISION"200210020000Z"DESCRIPTION"Extend ccasGrpCfgServiceType to include
trunkingService(8)."REVISION"9901180000Z"DESCRIPTION"Add ccasXgcpCfgTable to configure continuity test
(COT) tone frequencies.
Add object ccasGrpCfgServiceType for displaying service
type.
Extend ccsaGrpCfgType to include fgdOS, fgdEANA and
nullSignaling"::={ ciscoMgmt 85}--
-- ifEntry for the all type of Channel Associated Signal channel (CAS)
-- supports the ifGeneralInformationGroup of Cisco IF-MIB.
---- ifTable Comments
-- ============== ==================================================
-- ifIndex Each CAS channel is represented by an ifEntry.
-- ifDescr Textual CAS channel description.
-- ifType The IANA value of ds0(81)
--
-- ifSpeed contains 64000 for CAS channel.
-- ifPhysAddress contains an octet string of zero length.
--
-- ifAdminStatus Only support the read-only ifAdminStatus.
-- ifOperStatus The current operational status of the CAS channel
-- interface port. Note that dormant(5) is explicitly
-- being used as defined in RFC 1573.
-- ifLastChange Refer to RFC 1573.
-- ifLinkUpDownTrapEnable
-- Only support the read-only ifLinkUpDownTrapEnable.
-- It contains a 'disabled(2)' value.
-- ifConnectorPresent
-- Refer to RFC 1573.
-- ifHighSpeed contains a zero value.
-- ifName Refer to RFC 1573.
-- ifAlias Only support the read-only ifAlias. It contains an
-- octet string of zero length.
----
-- Relationship to the IETF Dial Control MIB (RFC 2128)
--
-- Associating and disassociating a CAS channel interface with
-- a connection can be explicitly handled using an ifStack. If a
-- call connection is established, the managed system stacks the call
-- associated voice encapsulation interface on top of CAS channel of
-- T1/E1.
-- Refer to the section 2.2.1 of RFC 2128 and the section 3.2.1 of
-- RFC 2127 for the detailed information.
--
-- Using ifStackTable
--
-- This section describes by example how to use ifStackTable to
-- represent the relationship of dial-up peer with ds0 and ds1
-- interfaces.
-- Examples given below are for illustration of active calls on
-- voice encapsulation peers via ds0 of DS1.
--
-- Example: A Voice Peer1 is being carried two active calls via two
-- ds0 interfaces and Voice Peer2 is being carried one active
-- call via one ds0 interface of the same DS1.
--
-- +=============+ +=====+
-- | Voice | |Voice|
-- | Peer1 | |Peer2|
-- +=============+ +=====+
-- | | | <==== appears active
-- | | | when the dial-up peer
-- | | | connects to CAS channel
-- +===+ +===+ +===+
-- |ds0| |ds0| |ds0| <==== CAS channels
-- +===+ +===+ +===+
-- | | |
-- +=====================+
-- | DS1 |
-- +=====================+
--
-- The assignment of the index values could for example be:
--
-- ifIndex Description
-- 1 voice peer 1 (type 103)
-- 2 voice peer 2 (type 103)
-- 3 ds0 #1 (type 81)
-- 4 ds0 #2 (type 81)
-- 5 ds0 #3 (type 81)
-- 7 ds1 (type 18)
--
--
-- The ifStackTable is then used to show the relationships between the
-- various interfaces.
--
-- ifStackTable Entries
--
-- HigherLayer LowerLayer
-- 0 1
-- 0 2
-- 1 3
-- 1 4
-- 2 5
-- 3 7
-- 4 7
-- 5 7
-- 7 0
--
--
-- The Signaling type of the DS0 group is enhanced to include null
-- signaling. When configured as null signaling, the DS0 group
-- can provide voice/data path.ccasIfObjects OBJECTIDENTIFIER::={ ciscoCasIfMIB 1}ccasDS1Objects OBJECTIDENTIFIER::={ ccasIfObjects 1}ccasGrpObjects OBJECTIDENTIFIER::={ ccasIfObjects 2}ccasChannelObjects OBJECTIDENTIFIER::={ ccasIfObjects 3}ccasVoiceCfgObjects OBJECTIDENTIFIER::={ ccasIfObjects 4}ccasXgcpCfgObjects OBJECTIDENTIFIER::={ ccasIfObjects 5}
ccasGrpGeneralObjects OBJECTIDENTIFIER::={ ccasGrpObjects 1}ccasGrpEMObjects OBJECTIDENTIFIER::={ ccasGrpObjects 2}ccasGrpLineObjects OBJECTIDENTIFIER::={ ccasGrpObjects 3}ccasGrpStaObjects OBJECTIDENTIFIER::={ ccasGrpObjects 4}ccasGrpABCDObjects OBJECTIDENTIFIER::={ ccasGrpObjects 5}--*********************************************************************
-- The CAS/DS0 Interface Groups
--*********************************************************************
-- [1] CAS/DS0 General Configuration for T1/E1
-- [2] CAS/DS0 General Configuration group
-- [3] CAS E&M group
-- [4] CAS FXO/SAO group
-- [5] CAS FXS/SAS group
-- [6] CAS custom ABCD bits configuration group
-- [7] CAS channel group--*********************************************************************
-- The CAS/DS0 General Configuration Table for T1/E1
--*********************************************************************ccasDs1IfCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasDs1IfCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS/DS0 General Configuration Table for T1/E1. It
contains the CAS/DS0 related standard configuration
information for T1/E1.
"::={ ccasDS1Objects 1}ccasDs1IfCfgEntry OBJECT-TYPESYNTAX CcasDs1IfCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the configuration table for each T1/E1.
The entry is created when a T1/E1 hardware is detected.
"INDEX{ ifIndex }::={ ccasDs1IfCfgTable 1}
CcasDs1IfCfgEntry ::=
SEQUENCE{
ccasDs1IfCfgDs0ChannelsConfigurable OCTETSTRING}ccasDs1IfCfgDs0ChannelsConfigurable OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..4))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains the bit map of the available DS0
channel in the DS1.
The MSB (most significant bit) is DS0 channel number 1.
The missing bytes is default to a value of 0.
A 1-bit indicates the channel is available for
configuration and a 0-bit indicates it isn't.
The length of this object is either 3 octets (for T1)
or 4 octets (for E1).
The most significant bit is transmitted first.
"::={ ccasDs1IfCfgEntry 1}--*********************************************************************
-- The CAS/DS0 Group General Configuration Table
--*********************************************************************
ccasGrpCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS/DS0 Group Standard Configuration Table. It
contains the general configuration information for the
CAS/DS0 group of T1/E1 interfaces.
"::={ ccasGrpGeneralObjects 1}ccasGrpCfgEntry OBJECT-TYPESYNTAX CcasGrpCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A CAS/DS0 group entry. Each entry consists of the CAS
group type and the CAS/DS0 group associated DS0
channels in a T1/E1.
The value of ccasGrpCfgDs0Channels must be specified
with at least one available DS0 channel in the CAS
group associated T1/E1 before a new row in this table
can become active(1).
The entry of this table can only be created if the
CAS/DS0 group associated DS1 ifEntry already exists.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasGrpCfgTable 1}
CcasGrpCfgEntry ::=SEQUENCE{
ccasGrpCfgIndex Integer32,
ccasGrpCfgType INTEGER,
ccasGrpCfgDs0Channels OCTETSTRING,
ccasGrpCfgServiceType INTEGER,
ccasGrpCfgRowStatus RowStatus}ccasGrpCfgIndex OBJECT-TYPESYNTAXInteger32(0..30)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary index that uniquely identifies a DS0 group
in a T1/E1.
"::={ ccasGrpCfgEntry 1}
ccasGrpCfgType OBJECT-TYPESYNTAXINTEGER{emWinkStart (1),emWinkStartFgd (2),emImmedStart (3),emDelayDial (4),fxsLoopStart (5),fxsGroundStart (6),sasLoopStart (7),sasGroundStart (8),r2Analog (9),r2Digital (10),r2Pulse (11),p7 (12),fxoLoopStart (13),
fxoGroundStart (14),fgdOS (15),nullSignaling (16),r1Itu (17),r1Modified (18),r1Turkey (19),fgdEANA (20)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Signaling type of the DS0 group.
emWinkStart - CAS E&M Wink Start.
emWinkStartFgd - CAS E&M Wink Start with Feature
group D.
emImmedStart - CAS E&M Immediate Start.
emDelayDial - CAS E&M Delay Dial.
fxsLoopStart - CAS FXS Loop Start.
fxsGroundStart - CAS FXS Ground Start.
sasLoopStart - CAS SAS Loop Start.
sasGroundStart - CAS SAS Ground Start.
r2Analog - R2 ITU Q411.
r2Digital - R2 ITU Q421.
r2Pulse - R2 ITU Supplement 7.
p7 - P7 switch.
fgdOS - Bellcore Feature Group D :
Operator Services Signaling
nullSignaling - 64k clear channel
r1Itu - R1 ITU.
r1Modified - R1 Modified.
r1Turkey - R1 Turkey.
fgdEANA - FGD Exchange Access North American.
"REFERENCE"EIA/TIA-464B, chapter 6.2.1.1 Signaling Interface Types.
ITU-T Q411 - Specifications of signalling system R2 line
signalling, analogue version.
ITU-T Q421 - Specifications of signalling system R2 line
signalling, digital version.
ITU-T R2 Supplement 7 - Specifications of signalling system
R2 line signalling, pulsed version.
Bellcore, TR-NPL-000258 - Feature Group D
section 3.4 for Exchange Access North American
section 3.6 for Operator Services Signaling
"DEFVAL{ emWinkStart }::={ ccasGrpCfgEntry 2}ccasGrpCfgDs0Channels OBJECT-TYPE
SYNTAXOCTETSTRING(SIZE(4))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object contains the bit map of the selected DS0
channels to be added into this group.
The MSB (most significant bit) is DS0 channel number 1.
For T1, only higher 24 bits are used to specify the
the CAS channels for the CAS group.
A 1-bit indicates the channel to be added into group
and a 0-bit indicates it isn't.
"DEFVAL{ '00000000'H }::={ ccasGrpCfgEntry 3}ccasGrpCfgServiceType OBJECT-TYPESYNTAXINTEGER{none (1),casServSw56 (2),casServModem (3),
casServAuto (4),sgcp (5),mgcp (6),other (7),trunkingService (8),h248 (9),ds0xconn (10)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specify the Service type of the CAS/DS0 group.
none - no service type
casServSw56 - sw56 service for CAS
casServModme - modem service for CAS
casServAuto - auto service for CAS
sgcp - Simple Gateway Control Protocol
(SGCP) service. Used when DS0 is
configured for null signaling.
mgcp - Media Gateway Control Protocol
(MGCP) service. Used when DS0 is
configured for null signaling.
other - none of the above and the below.
trunkingService -
This DS0 group is handled by
trunking service application.
h248 - ITU H.248 Media Gateway Control
service. Used when DS0 is
configured for null signaling.
ds0xconn - Used for DS0 cross connection.
"DEFVAL{ none }::={ ccasGrpCfgEntry 5}ccasGrpCfgRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify
or delete an existing row in this table. The
corresponding instance of ccasGrpCfgType can not be
modified while this object has the value 'active'.
"::={ ccasGrpCfgEntry 4}--*********************************************************************
-- The CAS Group E&M Standard Configuration Table
--*********************************************************************ccasGrpEMCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpEMCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS Group E&M Standard Configuration Table. It
contains the CAS E&M group standard configuration
information of T1/E1.
"::={ ccasGrpEMObjects 1}ccasGrpEMCfgEntry OBJECT-TYPESYNTAX CcasGrpEMCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the configuration table for each CAS E&M
Group in the T1/E1.
The entry is created when the ccasGrpCfgType is
configured as 'em' on a T1/E1 via configuration
command.
The entry is deleted when the CAS Group is
de-configured from T1/E1.
"INDEX{ ifIndex, ccasGrpCfgIndex }
::={ ccasGrpEMCfgTable 1}
CcasGrpEMCfgEntry ::=SEQUENCE{
ccasGrpEMCfgDialType INTEGER,
ccasGrpEMCfgDnisAni BITS}ccasGrpEMCfgDialType OBJECT-TYPESYNTAXINTEGER{dtmf (1),pulse (2),mf (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
mf - Multi-Frequency (MF) digit.
The default value of this object is dtmf(1).
"::={ ccasGrpEMCfgEntry 1}
ccasGrpEMCfgDnisAni OBJECT-TYPESYNTAXBITS{incomingDnis (0),incomingAni (1),outgoingDnis (2),outgoingAni (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specify the type of Destination Number Identification
Service (DNIS) and Automatic Number Identification
(ANI) support.
MF tone supports both ANI and DNIS services. The DTMF
tone only supports both incoming and outgoing DNIS.
incomingDnis - support incoming DNIS feature.
incomingAni - support incoming ANI feature.
outgoingDnis - support outgoing DNIS feature.
outgoingAni - support outgoing ANI feature.
The default value of this object is '00'H.
"::={ ccasGrpEMCfgEntry 2}
--*********************************************************************
-- The CAS Group E&M Timing Parameters Table
--*********************************************************************-- This table contains the CAS Group E&M timing parameters information.ccasGrpEMTmTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpEMTmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The E&M interface Timing Parameters table. It
contains the configuration of the various E&M signaling
protocol timing parameters.
"::={ ccasGrpEMObjects 2}ccasGrpEMTmEntry OBJECT-TYPESYNTAX CcasGrpEMTmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the E&M Timing Parameters Table for
each E&M interface."AUGMENTS{ ccasGrpEMCfgEntry }::={ ccasGrpEMTmTable 1}
CcasGrpEMTmEntry ::=SEQUENCE{
ccasGrpEMTmClearWaitDuration Integer32,
ccasGrpEMTmMaxWinkWaitDuration Integer32,
ccasGrpEMTmMaxWinkDuration Integer32,
ccasGrpEMTmDelayStart Integer32,
ccasGrpEMTmMaxDelayDuration Integer32,
ccasGrpEMTmMinDelayPulseWidth Integer32,
ccasGrpEMTmDigitDuration Integer32,
ccasGrpEMTmInterDigitDuration Integer32,
ccasGrpEMTmPulseRate Integer32,
ccasGrpEMTmPulseInterDigitDuration Integer32}ccasGrpEMTmClearWaitDuration OBJECT-TYPESYNTAXInteger32(200..2000)UNITS"milliseconds"
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Time of Inactive incoming seizure signal to declare call
cleared.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emWinkStart(1) or
emWinkStartFgd(2).
The default value of this object is 400 milliseconds."::={ ccasGrpEMTmEntry 1}ccasGrpEMTmMaxWinkWaitDuration OBJECT-TYPESYNTAXInteger32(100..5000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Maximum wink wait duration for sending out wink start
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object
is emWinkStart(1) or emWinkStartFgd(2).
The default value of this object is 200 milliseconds."::={ ccasGrpEMTmEntry 2}
ccasGrpEMTmMaxWinkDuration OBJECT-TYPESYNTAXInteger32(100..3000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Maximum wink duration for sending out wink start
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emWinkStart(1)
or emWinkStartFgd(2).
The default value of this object is 200 milliseconds."::={ ccasGrpEMTmEntry 3}ccasGrpEMTmDelayStart OBJECT-TYPESYNTAXInteger32(20..2000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION
"Timing of generation of outgoing delayed start signal
from detection of incoming seizure.
This object is relevant to the interfaces of the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 300 milliseconds."::={ ccasGrpEMTmEntry 4}ccasGrpEMTmMaxDelayDuration OBJECT-TYPESYNTAXInteger32(100..5000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Maximum delay signal duration for sending out delay dial
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 2000 milliseconds."::={ ccasGrpEMTmEntry 5}ccasGrpEMTmMinDelayPulseWidth OBJECT-TYPESYNTAXInteger32(0 | 140..5000)
UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Minimum delay-dial pulse duration for incoming call.
If the value of this object is 0, then no delay-dial
is sent to the far end for the incoming call.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 140 milliseconds."::={ ccasGrpEMTmEntry 6}ccasGrpEMTmDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF/MF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpCfgDialType
is dtmf or R2 tone.
The default value of this object is 100 milliseconds.
"::={ ccasGrpEMTmEntry 7}ccasGrpEMTmInterDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF/MF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpCfgDialType
is dtmf or R2 tone.
The default value of this object is 100 milliseconds.
"::={ ccasGrpEMTmEntry 8}ccasGrpEMTmPulseRate OBJECT-TYPESYNTAXInteger32(10..20)UNITS"pulses per second"
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpCfgDialType
is pulse.
The default value of this object is 10 pps.
"::={ ccasGrpEMTmEntry 9}ccasGrpEMTmPulseInterDigitDuration OBJECT-TYPESYNTAXInteger32(100..1000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing inter-digit timing in
milliseconds.
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpCfgDialType
is pulse.
The default value of this object is 500 milliseconds.
"::={ ccasGrpEMTmEntry 10}
--*********************************************************************
-- The CAS Group FXS/SAS Standard Configuration Table
--*********************************************************************ccasGrpLineCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpLineCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS Group FXS/SAS Standard Configuration Table. It
contains the CAS FXS/SAS group standard configuration
information of T1/E1.
"::={ ccasGrpLineObjects 1}ccasGrpLineCfgEntry OBJECT-TYPESYNTAX CcasGrpLineCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the configuration table for each CAS
FXS/SAS Group in the T1/E1.
The entry is created when the ccasGrpCfgType is
configured as 'fxs' or 'sas' on a T1/E1 via
configuration command. The entry is deleted when the
CAS Group is de-configured from T1/E1.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasGrpLineCfgTable 1}
CcasGrpLineCfgEntry ::=SEQUENCE{
ccasGrpLineCfgNumberRings Integer32,
ccasGrpLineCfgSupDisconnect TruthValue,
ccasGrpLineCfgDialType INTEGER}ccasGrpLineCfgNumberRings OBJECT-TYPESYNTAXInteger32(0..10)UNITS"rings"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The number of rings detected before closing loop.
If the value of this object is 0, then the managed
system answers immediately after the interface detects
a incoming seizure if the ccasGrpCfgType is
'fxsGroundStart' or 'sasGroundStart'.
The default value of this object is 1 ring.
"::={ ccasGrpLineCfgEntry 1}ccasGrpLineCfgSupDisconnect OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION" Specifies whether a supervisory disconnect signal will
be presented to the interface when the connected party
at the interface hangs up. this object is only relevant
to the ccasGrpCfgType is fxsLoopStart or sasLoopStart.
The default value of this object is 'true'.
"::={ ccasGrpLineCfgEntry 2}ccasGrpLineCfgDialType OBJECT-TYPESYNTAXINTEGER{dtmf (1),pulse (2)}MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"Specify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
The default value of this object is dtmf(1).
"::={ ccasGrpLineCfgEntry 3}--*********************************************************************
-- The FXS/SAS Timing Parameters Table
--*********************************************************************
-- This table contains the FXS/SAS interface timing parameters
-- information.ccasGrpLineTmTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpLineTmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The FXS/SAS interface Timing Parameters table. It
contains the configuration of the various FXS/SAS
signaling protocol timing parameters.
"::={ ccasGrpLineObjects 2}ccasGrpLineTmEntry OBJECT-TYPESYNTAX CcasGrpLineTmEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry in the FXS/SAS Timing Parameters Table for
each FXS/SAS interface."AUGMENTS{ ccasGrpLineCfgEntry }::={ ccasGrpLineTmTable 1}
CcasGrpLineTmEntry ::=SEQUENCE{
ccasGrpLineTmDigitDuration Integer32,
ccasGrpLineTmInterDigitDuration Integer32,
ccasGrpLineTmPulseRate Integer32,
ccasGrpLineTmPulseInterDigitDuration Integer32}ccasGrpLineTmDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpLineCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.
"::={ ccasGrpLineTmEntry 1}ccasGrpLineTmInterDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing
of the interfaces in the CAS group if
ccasGrpLineCfgDialType is dtmf.
The default value of this object is 100 milliseconds.
"::={ ccasGrpLineTmEntry 2}ccasGrpLineTmPulseRate OBJECT-TYPESYNTAXInteger32(10..20)
UNITS"pulses per second"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpStaCfgDialType
is pulse.
The default value of this object is 10 pps.
"::={ ccasGrpLineTmEntry 3}ccasGrpLineTmPulseInterDigitDuration OBJECT-TYPESYNTAXInteger32(100..1000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing inter-digit timing in
milliseconds. This object is relevant to the addressing
timing of the interfaces in the CAS group only if
ccasGrpStaCfgDialType is pulse.
The default value of this object is 500 milliseconds.
"::={ ccasGrpLineTmEntry 4}--*********************************************************************
-- The CAS Group FXO/SAO Standard Configuration Table
--*********************************************************************-- This table contains the configuration information of FXO/SAO signal
-- interface.ccasGrpStaCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpStaCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The FXO/SAO standard configuration table. It contains
FXO/SAO configuration parameters, one entry per FXO/SAO
interface.
The configuration information of this table is set by
its default setting when the CAS group is created by
the configuration commands.
"::={ ccasGrpStaObjects 1}ccasGrpStaCfgEntry OBJECT-TYPESYNTAX CcasGrpStaCfgEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry in the standard configuration table for
each FXO/SAO Group.
The entry is created when the ccasGrpCfgType is
configured as 'fxo' or 'sao' on a T1/E1 via
configuration command. The entry is deleted when the
CAS Group is de-configured from T1/E1.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasGrpStaCfgTable 1}
CcasGrpStaCfgEntry ::=SEQUENCE{
ccasGrpStaCfgNumberRings Integer32,
ccasGrpStaCfgDialType INTEGER}ccasGrpStaCfgNumberRings OBJECT-TYPESYNTAXInteger32(0..1000)UNITS"rings"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The number of rings sent before sending reorder to the
originator and releasing resources.
If the value of this object is 0, then sending
reorder to the originator is disabled.
The default value of this object is 20 rings.
"::={ ccasGrpStaCfgEntry 1}ccasGrpStaCfgDialType OBJECT-TYPESYNTAXINTEGER{dtmf (1),pulse (2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
The default value of this object is dtmf(1).
"::={ ccasGrpStaCfgEntry 2}--*********************************************************************
-- The FXO/SAO Timing Parameters Table
--*********************************************************************
-- This table contains the FXO/SAO interface timing parameters
-- information.ccasGrpStaTmTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpStaTmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The FXO/SAO interface Timing Parameters table. It
contains the configuration of the various FXO/SAO
signaling protocol timing parameters.
"::={ ccasGrpStaObjects 2}ccasGrpStaTmEntry OBJECT-TYPESYNTAX CcasGrpStaTmEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the FXO/SAO Timing Parameters Table for
each FXO/SAO interface."AUGMENTS{ ccasGrpStaCfgEntry }::={ ccasGrpStaTmTable 1}
CcasGrpStaTmEntry ::=SEQUENCE{
ccasGrpStaTmDigitDuration Integer32,
ccasGrpStaTmInterDigitDuration Integer32,
ccasGrpStaTmPulseRate Integer32,
ccasGrpStaTmPulseInterDigitDuration Integer32}ccasGrpStaTmDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpStaCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.
"::={ ccasGrpStaTmEntry 1}ccasGrpStaTmInterDigitDuration OBJECT-TYPESYNTAXInteger32(50..500)
UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing DTMF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpStaCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.
"::={ ccasGrpStaTmEntry 2}ccasGrpStaTmPulseRate OBJECT-TYPESYNTAXInteger32(10..20)UNITS"pulses per second"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpStaCfgDialType
is pulse.
The default value of this object is 10 pps.
"::={ ccasGrpStaTmEntry 3}ccasGrpStaTmPulseInterDigitDuration OBJECT-TYPESYNTAXInteger32(100..1000)UNITS"milliseconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Outgoing Pulse dialing inter-digit timing in
milliseconds. This object is relevant to the addressing
timing of the interfaces in the CAS group only if
ccasGrpStaCfgDialType is pulse.
The default value of this object is 500 milliseconds.
"::={ ccasGrpStaTmEntry 4}--*********************************************************************
-- The CAS group associated custom ABCD bits configuration Table
--*********************************************************************
-- This table contains the A/B/C/D bits handling parameters information.ccasGrpABCDCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasGrpABCDCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS group custom ABCD bits configuration table for
E1. It contains A/B/C/D bits handling objects, one
entry per CAS group on an E1 interface.
"::={ ccasGrpABCDObjects 1}ccasGrpABCDCfgEntry OBJECT-TYPESYNTAX CcasGrpABCDCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the custom ABCD configuration table for
each CAS Group on an E1 interface.
The entry is created when a CAS group is configured
on a E1. The entry is deleted when the CAS Group is
de-configured from E1.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasGrpABCDCfgTable 1}
CcasGrpABCDCfgEntry ::=SEQUENCE{
ccasGrpABCDCfgInvertBits BITS,
ccasGrpABCDCfgUnusedBits BITS}ccasGrpABCDCfgInvertBits OBJECT-TYPESYNTAXBITS{dBit (0),cBit (1),bBit (2),aBit (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specify the A/B/C/D bit mask to invert the A/B/C/D bits
value before the A/B/C/D bits are sent or
after the A/B/C/D bits are received.
1-bit - enable bit inversion.
0-bit - disable bit inversion.
The default value of this object is '00'H
"::={ ccasGrpABCDCfgEntry 1}ccasGrpABCDCfgUnusedBits OBJECT-TYPE
SYNTAXBITS{dBit (0),cBit (1),bBit (2),aBit (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specify the Unused A/B/C/D bit values to transmit.
If any A/B/C/D bit is unused, the bit values in this
object will be used to transmit for the unused
A/B/C/D bits.
The default value of this object is '00'H
"::={ ccasGrpABCDCfgEntry 2}--***********************************************************************
-- The CAS channel Standard Configuration Table
--***********************************************************************ccasChannelCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasChannelCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS channel Standard Configuration Table. It
contains the standard configuration information of CAS
channel of T1/E1.
"::={ ccasChannelObjects 1}ccasChannelCfgEntry OBJECT-TYPESYNTAX CcasChannelCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the configuration table for each CAS
channel. The entry is created when a CAS channel is
configured on a T1/E1 via configuration command. The
entry is deleted when the CAS channel is de-configured
from T1/E1.
"INDEX{ ifIndex }::={ ccasChannelCfgTable 1}
CcasChannelCfgEntry ::=SEQUENCE{
ccasChannelCfgDS1IfIndex InterfaceIndex,
ccasChannelCfgGroup Integer32,
ccasChannelCfgTimeSlot Integer32,
ccasChannelCfgBusyOut TruthValue}ccasChannelCfgDS1IfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"the ifIndex of this CAS channel associated T1/E1.
"::={ ccasChannelCfgEntry 1}ccasChannelCfgGroup OBJECT-TYPESYNTAXInteger32(0..30)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The CAS channel associated CAS group number.
"::={ ccasChannelCfgEntry 2}ccasChannelCfgTimeSlot OBJECT-TYPE
SYNTAXInteger32(1..31)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The CAS channel associated T1/E1 timeslot."::={ ccasChannelCfgEntry 3}ccasChannelCfgBusyOut OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The CAS channel busyout configuration.
true - the CAS channel is busied out.
false - the CAS is normal.
The default value for this object is 'false'.
"::={ ccasChannelCfgEntry 4}--***********************************************************************
-- The CAS channel Status Table
--***********************************************************************ccasChannelStatusTable OBJECT-TYPE
SYNTAXSEQUENCEOF CcasChannelStatusEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The CAS channel Status Table. It contains general
information about the status of CAS channel.
"::={ ccasChannelObjects 2}ccasChannelStatusEntry OBJECT-TYPESYNTAX CcasChannelStatusEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the status table for each CAS channel.
"AUGMENTS{ ccasChannelCfgEntry }::={ ccasChannelStatusTable 1}
CcasChannelStatusEntry ::=SEQUENCE{
ccasChannelStatusRecvSignalBits BITS,
ccasChannelStatusBusyOut TruthValue,
ccasChannelStatusInfoType INTEGER,
ccasChannelStatusXmitSignalBits BITS}ccasChannelStatusRecvSignalBits OBJECT-TYPESYNTAXBITS{dBit (0),cBit (1),bBit (2),aBit (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The receive ABCD signaling bits for the CAS channel.
aBit - the signaling bit in the 6th frame
bBit - the signaling bit in the 12th frame
cBit - the signaling bit in the 18th frame
dBit - the signaling bit in the 24th frame
the cBit and dBit are only valid for E1 or T1
interface is operating in extended superframe (ESF)
mode.
"REFERENCE"EIA/TIA-464B, chapter 6.2 Digital Signaling and Supervision
"::={ ccasChannelStatusEntry 1}ccasChannelStatusBusyOut OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The CAS channel busyout state.
true - the CAS channel is busied out.
false - the CAS is normal.
"::={ ccasChannelStatusEntry 2}ccasChannelStatusInfoType OBJECT-TYPESYNTAXINTEGER{unknown (1),speech (2),data56 (3),audio31 (4),audio7 (5),
video (6),fax (7),modem (8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Information Transfer Capability for the current
or last call.
unknown - If since system startup there has been no call
on this interface, this object has a value of
unknown(1).
speech - refers to a non-data connection
data56 - 56k data.
audio31 - audio 3.1 kHz; refers to data mode connections
audio7 - audio 7 kHz; refer to data mode connections;
'Unrestricted digital information with tones/
announcements'.
video - as defined in Q.931
fax - Facsimile
modem - V.3x modem
"REFERENCE"Q.931 [8], chapter 4.5.5, octet 3 of bearer capability
information element, combined with the User Rate
(as defined in octets 5 and 5a to 5d), if rate adoption
is being used."::={ ccasChannelStatusEntry 3}ccasChannelStatusXmitSignalBits OBJECT-TYPESYNTAXBITS{dBit (0),cBit (1),bBit (2),aBit (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The transmit ABCD signaling bits for the CAS channel.
aBit - the signaling bit in the 6th frame
bBit - the signaling bit in the 12th frame
cBit - the signaling bit in the 18th frame
dBit - the signaling bit in the 24th frame
the cBit and dBit are only valid for E1 or T1
interface is operating in extended superframe (ESF)
mode.
"REFERENCE"EIA/TIA-464B, chapter 6.2 Digital Signaling and Supervision
"::={ ccasChannelStatusEntry 4}--
-- Voice specific Configuration Table for a DS0 group
--ccasVoiceCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasVoiceCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The voice specific configuration Table. It contains
information about the voice related configuration
parameters for a CAS group.
"::={ ccasVoiceCfgObjects 1}ccasVoiceCfgEntry OBJECT-TYPESYNTAX CcasVoiceCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the voice specific configuration table for each
CAS/DS0 group of a DS1.
The entry is created if the associated CAS/DS0 group is
created and the voice hardware is detected to support the
voice capability for the CAS/DS0 group in the managed
system.
The entry is deleted when its associated CAS/DS0 group is
deleted.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasVoiceCfgTable 1}
CcasVoiceCfgEntry ::=SEQUENCE{
ccasVoiceCfgNoiseRegEnable TruthValue,
ccasVoiceCfgNonLinearProcEnable TruthValue,
ccasVoiceCfgMusicOnHoldThreshold Integer32,
ccasVoiceCfgInGain Integer32,
ccasVoiceCfgOutAttn Integer32,
ccasVoiceCfgEchoCancelEnable TruthValue,
ccasVoiceCfgEchoCancelCoverage INTEGER,
ccasVoiceCfgConnectionMode INTEGER,
ccasVoiceCfgConnectionNumber DisplayString,
ccasVoiceCfgInitialDigitTimeOut Integer32,
ccasVoiceCfgInterDigitTimeOut Integer32,
ccasVoiceCfgRegionalTone CountryCode
}ccasVoiceCfgNoiseRegEnable OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object indicates whether or not the background noise
should be played to fill silence gaps if VAD is activated.
The default value of this object is 'true'.
"::={ ccasVoiceCfgEntry 1}ccasVoiceCfgNonLinearProcEnable OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object indicates whether or not the Nonlinear Processing
is enabled for the interface.
The default value of this object is 'true'.
"::={ ccasVoiceCfgEntry 2}ccasVoiceCfgMusicOnHoldThreshold OBJECT-TYPESYNTAXInteger32(-70..-30)
UNITS"dBm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object specifies the Music On Hold Threshold for
the interface.
The default value of this object is -38 dBm.
"::={ ccasVoiceCfgEntry 3}ccasVoiceCfgInGain OBJECT-TYPESYNTAXInteger32(-6..14)UNITS"dB"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object contains the amount of gain inserted at the
receiver side of the interface. The input gain settings
only define a gain/loss relative to the 0 dB setting.
The absolute loss at the 0 dB setting could be
implementation dependent based on the desired network
loss plan.
The default value of this object is 0 dB (decibel).
"::={ ccasVoiceCfgEntry 4}ccasVoiceCfgOutAttn OBJECT-TYPESYNTAXInteger32(0..14)UNITS"dB"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object contains the amount of attenuation inserted
at the transmit side of the interface.
The output attenuation settings only define a loss
relative to the 0 dB setting.
The absolute loss at the 0 dB setting could be
implementation dependent based on the desired network
loss plan.
The default value of this object is 0 dB (decibel).
"::={ ccasVoiceCfgEntry 5}ccasVoiceCfgEchoCancelEnable OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"The object specifies whether or not the Echo Cancellation
is enabled for the interface.
The default value of this object is 'true'.
"::={ ccasVoiceCfgEntry 6}ccasVoiceCfgEchoCancelCoverage OBJECT-TYPESYNTAXINTEGER{echoCanceller8ms (1),echoCanceller16ms (2),echoCanceller24ms (3),echoCanceller32ms (4),echoCanceller64ms (5),echoCanceller128ms(6)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object specifies the Echo Canceller coverage for
the interface. This object is valid if the
ccasVoiceCfgEchoCancelEnable object is 'true'.
echoCanceller8ms - 8 milliseconds echo canceller coverage.
echoCanceller16ms - 16 milliseconds echo canceller coverage.
echoCanceller24ms - 24 milliseconds echo canceller coverage.
echoCanceller32ms - 32 milliseconds echo canceller coverage.
echoCanceller64ms -
64 milliseconds echo canceller coverage.
echoCanceller128ms-
128 milliseconds echo canceller coverage.
The default value of this object is echoCanceller8ms.
"::={ ccasVoiceCfgEntry 7}ccasVoiceCfgConnectionMode OBJECT-TYPESYNTAXINTEGER{normal (1),trunk (2),plar (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The object indicates the connection mode of the interface.
normal - the interface acts normally to handle incoming
and outgoing call.
trunk - the interface acts in trunking mode. trunking mode
causes two interfaces (on either the same or
different routers) to be always conferenced
together, and for telephony signaling to be
passed transparently through the VoIP system
rather than trapped and interpreted by the session
application on the router(s).
plar - the interface acts in PLAR (private line automatic
ringdown) mode. PLAR is handled by associating a
peer directly with an interface such that when the
interface goes off-hook, that peer is used to setup
the second call leg and conference them together
without the caller having to dial any digits.
"::={ ccasVoiceCfgEntry 8}ccasVoiceCfgConnectionNumber OBJECT-TYPESYNTAXDisplayString(SIZE(0..32))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This is the E.164 phone number that is used to
establish connection with trunking mode or PLAR mode.
If the ccasVoiceCfgConnectionMode is 'normal', then this
object will be a zero length string.
"::={ ccasVoiceCfgEntry 9}ccasVoiceCfgInitialDigitTimeOut OBJECT-TYPESYNTAXInteger32(0..120)UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This is the initial digit timeout that indicates the amount
of time the managed system waits for an initial input digit
from the caller. The timer is activated when the call is
accepted and is deactivated upon digit input. If the timer
expires, the caller is signaled through the appropriate
tone and the call is abandoned. The value of zero disables
the timer.
The default value of this object is 10 seconds.
"::={ ccasVoiceCfgEntry 10}ccasVoiceCfgInterDigitTimeOut OBJECT-TYPE
SYNTAXInteger32(0..120)UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This is the inter-digit timeout that indicates the amount
of time the managed system waits for a subsequent input
digit from the caller. The timer is started upon receipt of
an input digit and restarted as each digit is received
until the destination address is identified. If the timer
expires and no destination address is identified, the
caller is signaled through the appropriate tone and the
call is abandoned. The value of zero disables the timer.
The default value of this object is 10 seconds.
"::={ ccasVoiceCfgEntry 11}ccasVoiceCfgRegionalTone OBJECT-TYPESYNTAX CountryCode
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object contains the current regional setting for
the call progress tone to be used by this CAS group.
"::={ ccasVoiceCfgEntry 12}--
-- XGCP Configuration Table for a DS0 group
--ccasXgcpCfgTable OBJECT-TYPESYNTAXSEQUENCEOF CcasXgcpCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The XGCP configuration Table contains
information about DS0 usage by XGCP(SGCP/MGCP).
XGCP is meant to represent both Simple Gateway Control
Protocol (SGCP) and Media Gateway Control Protocol (MGCP).
"::={ ccasXgcpCfgObjects 1}ccasXgcpCfgEntry OBJECT-TYPESYNTAX CcasXgcpCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the configuration table for each
DS0 group of a DS1.
The entry is created if the DS0 group is configured as
null-signaling and ccasGrpCfgServiceType is configured
as either sgcp or mgcp.
The entry is deleted when the signaling type is configured
as non null-signaling.
"INDEX{ ifIndex, ccasGrpCfgIndex }::={ ccasXgcpCfgTable 1}
CcasXgcpCfgEntry ::=SEQUENCE{
ccasXgcpCfgCotToneCo1 Integer32,
ccasXgcpCfgCotToneCo2 Integer32}ccasXgcpCfgCotToneCo1 OBJECT-TYPESYNTAXInteger32(280..3800)UNITS"hertz"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the continuity test tone
frequencies for co1. Co1 is the COT tone frequency from
the terminating switch in transponder mode and is from
the originating switch in loopback mode.
"REFERENCE"Bellcore GR-317-CORE spec, Rev 3, Nov. 1996, section
3.1.1.3.
"::={ ccasXgcpCfgEntry 1}ccasXgcpCfgCotToneCo2 OBJECT-TYPESYNTAXInteger32(280..3800)UNITS"hertz"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the continuity test tone
frequencies for co2. Co2 is the COT tone frequency from
the originating switch only in transponder mode.
"REFERENCE"Bellcore GR-317-CORE spec, Rev 3, Nov. 1996, section
3.1.1.3.
"::={ ccasXgcpCfgEntry 2}--***********************************************************************
-- Conformance and compliance statements
--***********************************************************************
-- conformance informationccasIfMIBConformance
OBJECTIDENTIFIER::={ ciscoCasIfMIB 3}ccasIfMIBCompliances
OBJECTIDENTIFIER::={ ccasIfMIBConformance 1}ccasIfMIBGroups
OBJECTIDENTIFIER::={ ccasIfMIBConformance 2}-- compliance statementsccasIfMIBCompliance MODULE-COMPLIANCESTATUSobsolete-- superseded by ccasIfMIBComplianceRev1DESCRIPTION"The compliance statement for entities which implement
the Cisco Voice Digital interface MIB"MODULE-- compliance to this moduleMANDATORY-GROUPS{
ccasIfDS1Group,
ccasGeneralInfoGroup
}GROUP ccasEMGroup
DESCRIPTION"The CAS E&M group is mandatory for T1/E1 that
supports CAS E&M signal interface.
"GROUP ccasLineGroup
DESCRIPTION"The CAS Line group is mandatory for T1/E1 that
supports CAS FXO/SAO signal interfaces.
"GROUP ccasStaGroup
DESCRIPTION"The CAS Station group is mandatory for T1/E1
that supports CAS FXS/SAS signal interfaces.
"GROUP ccasCustomABCDGroup
DESCRIPTION"The CAS custom ABCD bits configuration group is
mandatory for E1 that supports CAS signal
interfaces.
"GROUP ccasVoiceGroup
DESCRIPTION"The CAS Voice group is mandatory for a CAS group
that supports voice/fax call capability.
"OBJECT ccasGrpCfgType
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."
OBJECT ccasGrpCfgDs0Channels
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."OBJECT ccasGrpCfgRowStatus
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."OBJECT ccasGrpEMCfgDialType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasGrpEMCfgDnisAni
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasGrpABCDCfgInvertBits
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasGrpABCDCfgUnusedBits
MIN-ACCESSread-onlyDESCRIPTION
"Write access is not required."OBJECT ccasVoiceCfgNoiseRegEnable
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgNonLinearProcEnable
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgMusicOnHoldThreshold
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgInGain
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgOutAttn
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgEchoCancelEnable
MIN-ACCESSread-only
DESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgEchoCancelCoverage
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgConnectionMode
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgConnectionNumber
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgInitialDigitTimeOut
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgInterDigitTimeOut
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasVoiceCfgRegionalTone
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ ccasIfMIBCompliances 1}ccasIfMIBComplianceRev1 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
the Cisco Voice Digital interface MIB"MODULE-- compliance to this moduleMANDATORY-GROUPS{
ccasIfDS1Group,
ccasGeneralInfoGroupRev1
}GROUP ccasEMGroup
DESCRIPTION"The CAS E&M group is mandatory for T1/E1 that
supports CAS E&M signal interface.
"GROUP ccasLineGroup
DESCRIPTION"The CAS Line group is mandatory for T1/E1 that
supports CAS FXO/SAO signal interfaces.
"
GROUP ccasStaGroup
DESCRIPTION"The CAS Station group is mandatory for T1/E1
that supports CAS FXS/SAS signal interfaces.
"GROUP ccasCustomABCDGroup
DESCRIPTION"The CAS custom ABCD bits configuration group is
mandatory for E1 that supports CAS signal
interfaces.
"GROUP ccasVoiceGroup
DESCRIPTION"The CAS Voice group is mandatory for a CAS group
that supports voice/fax call capability.
"GROUP ccasChannelInfoGroup
DESCRIPTION"The Channel Info group is mandatory for
providing channel signaling information
applicable to Channel Associated Signaling
interfaces.
"GROUP ccasXgcpCfgGroup
DESCRIPTION"The XGCP Cfg group is mandatory for DS0 group
that supports XGCP protocol entity.
"OBJECT ccasGrpCfgType
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."OBJECT ccasGrpCfgDs0Channels
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."OBJECT ccasGrpCfgRowStatus
MIN-ACCESSread-onlyDESCRIPTION"Create/Write access is not required."OBJECT ccasGrpEMCfgDialType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasGrpEMCfgDnisAni
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT ccasGrpABCDCfgInvertBits
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."
OBJECT ccasGrpABCDCfgUnusedBits
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ ccasIfMIBCompliances 2}-- units of conformanceccasIfDS1Group OBJECT-GROUPOBJECTS{
ccasDs1IfCfgDs0ChannelsConfigurable
}STATUScurrentDESCRIPTION"The collection of objects providing CAS/DS0 related
T1/E1 information.
"::={ ccasIfMIBGroups 1}ccasGeneralInfoGroup OBJECT-GROUPOBJECTS{
ccasGrpCfgType,
ccasGrpCfgDs0Channels,
ccasGrpCfgRowStatus,
ccasChannelCfgDS1IfIndex,
ccasChannelCfgGroup,
ccasChannelCfgTimeSlot,
ccasChannelCfgBusyOut,
ccasChannelStatusRecvSignalBits,
ccasChannelStatusBusyOut,
ccasChannelStatusInfoType,
ccasChannelStatusXmitSignalBits
}STATUSobsolete-- superseded by ccasGeneralInfoGroupRev1DESCRIPTION"A collection of objects providing general information
applicable to Channel Associated Signaling interfaces.
"::={ ccasIfMIBGroups 2}ccasEMGroup OBJECT-GROUPOBJECTS{
ccasGrpEMCfgDialType,
ccasGrpEMCfgDnisAni,
ccasGrpEMTmClearWaitDuration,
ccasGrpEMTmMaxWinkWaitDuration,
ccasGrpEMTmMaxWinkDuration,
ccasGrpEMTmDelayStart,
ccasGrpEMTmMaxDelayDuration,
ccasGrpEMTmMinDelayPulseWidth,
ccasGrpEMTmDigitDuration,
ccasGrpEMTmInterDigitDuration,
ccasGrpEMTmPulseRate,
ccasGrpEMTmPulseInterDigitDuration
}STATUScurrentDESCRIPTION"A collection of objects providing information applicable
to the CAS E&M signal interfaces.
"::={ ccasIfMIBGroups 3}ccasLineGroup OBJECT-GROUPOBJECTS{
ccasGrpLineCfgNumberRings,
ccasGrpLineCfgSupDisconnect,
ccasGrpLineCfgDialType,
ccasGrpLineTmDigitDuration,
ccasGrpLineTmInterDigitDuration,
ccasGrpLineTmPulseRate,
ccasGrpLineTmPulseInterDigitDuration
}STATUScurrentDESCRIPTION"A collection of objects providing information applicable
to the CAS FXS/SAS signal interfaces.
"::={ ccasIfMIBGroups 4}ccasStaGroup OBJECT-GROUPOBJECTS{
ccasGrpStaCfgNumberRings,
ccasGrpStaCfgDialType,
ccasGrpStaTmDigitDuration,
ccasGrpStaTmInterDigitDuration,
ccasGrpStaTmPulseRate,
ccasGrpStaTmPulseInterDigitDuration
}STATUScurrentDESCRIPTION"A collection of objects providing information applicable
to the CAS FXO/SAO signal interfaces.
"::={ ccasIfMIBGroups 5}ccasCustomABCDGroup OBJECT-GROUPOBJECTS{
ccasGrpABCDCfgInvertBits,
ccasGrpABCDCfgUnusedBits
}STATUScurrentDESCRIPTION"A collection of objects providing ABCD bits
configuration information applicable to the CAS group
on E1 interface.
"::={ ccasIfMIBGroups 6}ccasVoiceGroup OBJECT-GROUPOBJECTS{
ccasVoiceCfgNoiseRegEnable,
ccasVoiceCfgNonLinearProcEnable,
ccasVoiceCfgMusicOnHoldThreshold,
ccasVoiceCfgInGain,
ccasVoiceCfgOutAttn,
ccasVoiceCfgEchoCancelEnable,
ccasVoiceCfgEchoCancelCoverage,
ccasVoiceCfgConnectionMode,
ccasVoiceCfgConnectionNumber,
ccasVoiceCfgInitialDigitTimeOut,
ccasVoiceCfgInterDigitTimeOut,
ccasVoiceCfgRegionalTone
}STATUScurrentDESCRIPTION"A collection of objects providing information applicable
to the CAS/DS0 group that supports voice capability.
"::={ ccasIfMIBGroups 7}ccasGeneralInfoGroupRev1 OBJECT-GROUPOBJECTS{
ccasGrpCfgType,
ccasGrpCfgDs0Channels,
ccasGrpCfgServiceType,
ccasGrpCfgRowStatus
}STATUScurrentDESCRIPTION"A collection of objects providing general information
applicable to CAS/DS0 interfaces.
"::={ ccasIfMIBGroups 8}ccasChannelInfoGroup OBJECT-GROUPOBJECTS{
ccasChannelCfgDS1IfIndex,
ccasChannelCfgGroup,
ccasChannelCfgTimeSlot,
ccasChannelCfgBusyOut,
ccasChannelStatusRecvSignalBits,
ccasChannelStatusBusyOut,
ccasChannelStatusInfoType,
ccasChannelStatusXmitSignalBits
}STATUScurrentDESCRIPTION"A collection of objects providing channel signaling
information applicable to Channel Associated Signaling
interfaces.
"::={ ccasIfMIBGroups 9}ccasXgcpCfgGroup OBJECT-GROUPOBJECTS{
ccasXgcpCfgCotToneCo1,
ccasXgcpCfgCotToneCo2
}STATUScurrentDESCRIPTION"A collection of objects providing XGCP specific
information applicable to DS0.
"::={ ccasIfMIBGroups 10}END